Activar enganche de remolque tras reequipamiento en Audi A5 II (F5)

Guía de codificación para Activar enganche de remolque tras reequipamiento en Audi A5 II (F5). Compatible con VCDS / VAG-COM · OBDeleven (cuando la propia ficha lo indica). La ruta manual mostrada está documentada con VCDS / VAG-COM. Consulta el módulo, el tipo de codificación, el canal o Byte/Bit y los valores necesarios antes de realizar el cambio.

¿Qué hace esta codificación?

Enables trailer / towbar retrofit. Please note! Adaptation in motor control unit 01 is not accepted for some models. In this case, the coding can be ignored. Control units that are not installed can also be ignored. Please note that certain coding steps must be carried out according to the part numbers installed (camera).

💡

¿Es tu primera codificación? Consulta qué son un Byte, un Bit, Coding y Adaptation y dónde encontrarlos.

Antes de modificar: guarda o fotografía siempre el valor original. Una codificación incorrecta puede provocar fallos y algunas funciones dependen del hardware y versión de centralita.

Estado	🟠 Depende de centralita/software
Módulo	19 - CAN Gateway
Tipo	Procedure
Herramientas compatibles	VCDS / VAG-COM · OBDeleven (cuando la propia ficha lo indica)
Procedimiento documentado con	VCDS / VAG-COM
Security Access	31347 / 24990 / 71679 / 14117 / 20103

Operaciones técnicas

Operación	Módulo	Tipo	Canal / Byte-Bit	Valor
Operación 1	19 - CAN Gateway	Long Coding		`Installation List 5 – Tick: “69 – Trailer ” in the list 6 – Save coding`
Operación 2	01 - Motor	Long Coding		`byte “05 ” Then check Bit “4 ”: “Trailer installed`
Operación 3	09 - Cent. Elect	Procedure	`01 Trailer Connector Diagnosis active → Networking trailer connection device → built in`	`built in” and confirm`
Operación 4	03 - ABS brake	Adaptation	`trailer stabilization → Activated`	`Activated ” and confirm`
Operación 5	10 - Assistance stationnt	Long Coding		`byte “03 ” Then check Bit 0-1 “01 Trailer Hitch installed (manually removable)`
Operación 6	13 - Auto Dist. Reg	Long Coding		`byte “02 ” (camera 5Q0) or “03 ” (camera 2Q0/3Q0) Then check Bit 3 “Trailer Recognition Control Module installed`
Operación 7	34 - Correct. Assiet	Long Coding		`byte “00 ” Then check bit 7 (“trailer, 0 = not installed / 1 = installed”)`
Operación 8	3C - Lane Change	Long Coding		`byte “02 ” (camera 5Q0) or “00 ” (camera 2Q0/3Q0) Then check Bit 4-7 “10 or 20 ECU for draw bar, with ECU for draw bar`
Operación 9	6C - Camera recul	Long Coding		`byte “04 ” Then check bit 0 (“equipment_ahk, installed”)`
Operación 10	6D - Elect. Trunk	Long Coding		`byte “01 ” Then check bit 7 (“trailer, 0 = not installed / 1 = installed”)`
Operación 11	A5 - Frt. Sens. Drv. Assist	Long Coding		`byte “05 ” (Camera 2Q0) Then set bit 4 (“AAG, 0 = not_coded / 1 = coded”)`
Operación 12	69 - Trailer	Long Coding		`byte “04 ” Then check Bit 0-7 “02 Terminal 30 output switched (pin 10) Trailer connected`

Vehículos compatibles

Audi A5 II (F5) · 2016–2024

Procedimiento manual documentado con VCDS / VAG-COM

1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.
2 – Switch on the ignition and run the VCDS program. Line 1:
3 – Click on “Select” , then click on “
19 – CAN Gateway ”.
4 – Select “Installation List
5 – Tick: “
69 – Trailer ” in the list
6 – Save coding Line 2:
3 – Click on “Select” , then click on “01 – Motor ”.
4 – Click on “ Coding – 07 ” then click on “Long Coding Helper ”.
5 – Select byte “05 ” Then check Bit “4 ”: “Trailer installed ”. Line 3:
3 – Click on “Select ” then click on “. 09 – Cent. Elect. ”. For power plants with coding:
4 – Click on “Coding – 07 ” then click on “Long Coding Helper ”
5 – Choose byte “01 ” Then in this “Bit 0-7 ” drop-down menu, select “01 Trailer Connector Diagnosis active ”. Or Byte “01 ” check Bit 1 “Trailer Hitch Control Module Installed ”. For power plants without coding :
4 – Click on “Security Access – 16 ” then enter the code “31347 ”.
5 – Click on “Adaptation – 10 ”.
6 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, choose “Networking trailer connection device ”.
7 – On this same page, there’s a second drop-down menu at the bottom of the page. On this menu, select “built in” and confirm. Line 4:
3 – Click on “Select ” then click on “03 – ABS brake ”.
4 – Click on “Security Access – 16 ” then enter the code “24990 ”.
6 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, choose “trailer stabilization ”.
7 – On this same page, there’s a second drop-down menu at the bottom of the page. On this, select “Activated ” and confirm. Line 5:
10 – Assistance stationnt ”.
4 – Click on “Security Access – 16 ” then enter code “71679 ” (optional code)
5 – Click on “ Coding – 07 ” then click on “Long Coding Helper ”.
6 – Select byte “03 ” Then check Bit 0-1 “01 Trailer Hitch installed (manually removable)”. Line 6:
3 – Click on “Select ” then click on “.
13 – Auto Dist. Reg. “.
4 – Click on “Security Access – 16 ” then enter the code “14117 ” or “20103 ”.
6 – Select byte “02 ” (camera 5Q0) or “03 ” (camera 2Q0/3Q0) Then check Bit 3 “Trailer Recognition Control Module installed”. Line 7:
34 – Correct. Assiet. “.
5 – Select byte “00 ” Then check bit 7 (“trailer, 0 = not installed / 1 = installed”) Line 8:
3 – Click on “Select” , then click on “3C – Lane Change ”.
5 – Select byte “02 ” (camera 5Q0) or “00 ” (camera 2Q0/3Q0) Then check Bit 4-7 “10 or 20 ECU for draw bar, with ECU for draw bar”. Line 9:
3 – Click on “Select” , then click on “6C – Camera recul ”.
5 – Select byte “04 ” Then check bit 0 (“equipment_ahk, installed”) Line 10:
3 – Click on “Select ” then click on “. 6D – Elect. Trunk “.
5 – Select byte “01 ” Then check bit 7 (“trailer, 0 = not installed / 1 = installed”) Line 11:
3 – Click on “Select ” then click on “. A5 – Frt. Sens. Drv. Assist “.
4 – Click on “Security Access – 16 ” then enter the code “20103 ”.

Observaciones

Conservar las condiciones, variantes de hardware/SFD y alternativas descritas en los pasos de la fuente.