Activar Audi Traffic Jam Assist en Audi A5 II (F5)

Guía de codificación para Activar Audi Traffic Jam Assist en Audi A5 II (F5). Compatible con VCDS / VAG-COM · OBDeleven (cuando la propia ficha lo indica). La ruta manual mostrada está documentada con VCDS / VAG-COM. Consulta el módulo, el tipo de codificación, el canal o Byte/Bit y los valores necesarios antes de realizar el cambio.

¿Qué hace esta codificación?

activates Audi’s Traffic Jam Assist (TJA) (with vehicle equipped with Pre-Sense). The Traffic Jam Assistant can take over steering at speeds of up to 65 km/h on well-maintained roads in the event of traffic jams. The system uses radar and ultrasonic sensors as well as the front camera to guide the vehicle by gently adjusting the steering and following the traffic ahead within the system’s limits. The traffic jam assistant uses road markings and other vehicles on the road to orientate itself. Watch out! There are 4 lines of coding to do here. (Use experimental data)

💡

¿Es tu primera codificación? Consulta qué son un Byte, un Bit, Coding y Adaptation y dónde encontrarlos.

Antes de modificar: guarda o fotografía siempre el valor original. Una codificación incorrecta puede provocar fallos y algunas funciones dependen del hardware y versión de centralita.

Estado	🟠 Depende de centralita/software
Módulo	13 - Auto Dist. Reg
Tipo	Procedure
Herramientas compatibles	VCDS / VAG-COM · OBDeleven (cuando la propia ficha lo indica)
Procedimiento documentado con	VCDS / VAG-COM

Operaciones técnicas

Operación	Módulo	Tipo	Canal / Byte-Bit	Valor
Operación 1	13 - Auto Dist. Reg	Long Coding		`Bit 2 “Emergency_Assist” check Bit 7 “Dense_traffic” Byte 06 check Bit 3 “Emergency_steer_assist`
Operación 2	A5 - Frt Sens. Drv	Long Coding	`Byte 16 → Bit 5`	`byte 16 Then tick Bit 5 “STA`
Operación 3	44 - Steering assistance	Long Coding		`Bit 0 “Traffic Jam Guidance Assist`
Operación 4	5F - Electronic Information	Adaptation	`Line 4: 3 – Click on “ Select” , then click on “5F – Electronic Information ”. 4 – Click on “Adaptation – 10 ” 5 – Select channels : Car_Function_Adaptations_Gen2 > front_traffic_assist_0x41 > activated Car_Function_Adaptations_Gen2 > front_traffic_assist_0x41`	`channels : Car_Function_Adaptations_Gen2 > front_traffic_assist_0x41 > activated Car_Function_Adaptations_Gen2 > front_traffic_assist_0x41_msg_bus > terminal 15`

Vehículos compatibles

Audi A5 II (F5) · 2016–2024

Procedimiento manual documentado con VCDS / VAG-COM

1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.
2 – Switch on the ignition and run the VCDS program. Line 1:
3 – Click on “ Select” then click on “
13 – Auto Dist. Reg ” .
4 – Click on “Coding – 07 ” then click on “Long Coding Helper ”.
5 – Select Byte 01 check Bit 3 “Traffic_jam_dependent_linear_tracking” check Bit 4 “Assistent_for_traffic_hold_up” Byte 02 check Bit 0 “Automatic_driveaway_by_pretrigger” check Bit 1 “Automatic_driveaway_after_short_stop” check Bit 2 “Driveaway_by_triggerleaver” check Bit 4 “Curve_assistent” Byte 03 Check Bit 5 “Traffic_jam_assistant_in_car_menu”. Byte 04 check Bit 2 “Emergency_Assist” check Bit 7 “Dense_traffic” Byte 06 check Bit 3 “Emergency_steer_assist”. Line 2:
3 – Click on “ Select” , then click on “Select”. A5 – Frt Sens. Drv ” .
5 – Choose byte 16 Then tick Bit 5 “STA”. Line 3:
3 – Click on “ Select” , then click on “
44 – Steering assistance ”.
4 – Click on “Coding – 07 ” and then click on “Long Coding Helper ”.
5 – Select Byte 02 check Bit 0 “Heading Control Assistant”. Byte 06 check Bit 0 “Traffic Jam Guidance Assist”. Line 4:
3 – Click on “ Select” , then click on “5F – Electronic Information ”.
4 – Click on “Adaptation – 10 ”
5 – Select channels : Car_Function_Adaptations_Gen2 > front_traffic_assist_0x41 > activated Car_Function_Adaptations_Gen2 > front_traffic_assist_0x41_msg_bus > terminal 15

Observaciones

Conservar las condiciones, variantes de hardware/SFD y alternativas descritas en los pasos de la fuente.